题目内容（请给出正确答案）

[主观题]

The switches shown in the diagram, Core and Core2, are both Catalyst 2950s. The addressing

scheme for each company site is as follows:Router Ethernet port - 1st usable addressCore - 2nd usable addressCore2 - 3rd usable addressFor this network, which of the following commands must be configured on Core2 to allow it to be managed remotely from any subnet on the network？（）

The switches shown in the diagram, Core and Core2,

A.Core2(config)# interface f0/0 Core2(config-if)# ip address 192.168.1.10 255.255.255.248

B.Core2(config)# interface vlan 1 Core2(config-if)# ip address 192.168.1.11 255.255.255.248

C.Core2(config)# line con 0 Core2(config-line)# password cisco

D.Core2(config)# line vty 0 4 Core2(config-line)# password cisco

E.Core2(config)# ip default-gateway 192.168.1.9

F.Core2(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.8

查看答案

如搜索结果不匹配，请联系老师获取答案

您可能会需要：

重置密码查看订单联系客服

安装赏学吧APP，拍照搜题省时又省心！

更多“The switches shown in the diag…”相关的问题

第1题

A.one

B.six

C.twelve

D.two

点击查看答案

第2题

Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the h

osts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem？（）

Refer to the exhibit.All switch ports are assigned

A.The access link needs to be configured in multiple VLANs.

B.The link between the switches is configured in the wrong VLAN.

C.The link between the switches needs to be configured as a trunk.

D.VTP is not configured to carry VLAN information between the switches.

E.Switch IP addresses must be configured in order for traffic to be forwarded between the switches

点击查看答案

第3题

What is the purpose of the command shown below vtp password Fl0r1da（）。

A.It is used to validate the sources of VTP advertisements sent between switches.

B.It is used to access the VTP server to make changes to the VTP configuration.

C.It allows two VTP servers to exist in the same domain, each configured with different passwords.

D.It is the password required when promoting a switch from VTP client mode to VTP server mode.

E.It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.

点击查看答案

第4题

What is the purpose of the command shown below？vtp password Fl0r1da（）

A. It is used to validate the sources of VTP advertisements sent between switches.

B. It is used to access the VTP server to make changes to the VTP configuration.

C. It allows two VTP servers to exist in the same domain, each configured with different passwords.

D. It is the password required when promoting a switch from VTP client mode to VTP server mode.

E. It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.

点击查看答案

第5题

Refer to the exhibit. You want to minimize the downtime that results from supervisor engin

e switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan？（）

Refer to the exhibit. You want to minimize the dow

A. Stateful Switchover for Cisco Nonstop Forwarding only works with BGP.

B. Stateful Switchover for Cisco Nonstop Forwarding must be configured on all adjacent routers.

C. Cisco Nonstop Forwarding with Stateful Switchover helper mode is not supported on the adjacent router.

D. Cisco Nonstop Forwarding with Stateful Switchover helper mode for OSPF has been promiscuousstandardized and is supported on the adjacent router.

点击查看答案

第6题

Which statement is true about a running session that belongs to the online transaction processing （OLTP) group？（）

Which statement is true about a running session th

A. It permanently switches to the low_group consumer group if the session exceeds 10,000 I/O requests or 2,500 MB of data transfer.

B. It performs the first 10000 I/O requests or 2,500 MB of data transfer in the LOW-GROUP consumer group, and then switches to the original group.

C. It switches to the LOW_GROUP consumer group if the session exceeds 10000 I/O requests or 2500 MB of data transfer and returns to the original group after the operation.

D. It switches to the LOW_GROUP consumer group if the session exceeds 10000 I/O requests or 2500MB of data transfer for queries, but not for data manipulation language (DML) operations.

点击查看答案

第7题

Thank you for making me feel important and ______ me that I could make a difference.

A.show

B.showing

C.showed

D.Shown

点击查看答案

第8题

I have been waiting for him for the last twenty minutes, but he hasn't（)yet.

A.shown off

B.shown up